Category
Tools
15 families in Tools.
What this category is for
Tools are the attachments that do a job a bucket cannot: break a surface, pull roots, level ground or hold material. Sieruta builds them in Ostrołęka, Poland, from Hardox and Strenx steel, and the range follows the work a groundwork or landscaping crew meets through the season. Asphalt cutters open a road surface along a clean line before a trench is dug. Rippers and multi-rippers loosen frozen ground, hard clay and soft rock so a bucket can lift it. The DuoRIP pulls stumps and root balls out whole. Grading beams finish a slope or a bed in long passes, and there is a lighter beam drawn for mini excavators so the machine keeps its stability. Land rakes and root rakes clear cut brush and roots while soil falls back on the plot. A hydraulic thumb turns the bucket into a grab for pipe, stone and timber. Every family is drawn for a carrier weight band and takes the same bracket systems as our buckets, so a tool goes on the coupler you already run.
15 of 15 product families
Full-size excavator attachments
NON-BUCKET ATTACHMENTS
Attachments other than buckets: grading beams for finishing, single and multi rippers for hard ground, and asphalt cutters for removing pavement.
Hydraulic Thumb for Excavator
The TH hydraulic thumb sits on the dipper stick and grips against the bucket, so the excavator can pick up and hold rocks, logs, pipes and debris.
On requestView product
AC - excavator asphalt cutters
Asphalt cutter with a 450 mm steel disc for excavators from 12 to 30 t.
On requestView product
MR - heavy duty excavator multi-ripper
The MR multi-ripper breaks compacted ground with five legs at once rather than one point, so a single pass loosens a wider strip and leaves smaller pieces to load.
On requestView product
RIP - heavy duty ripper
The RIP is a single shank ripper for excavators, with a protector over the shank.
On requestView product
DuoRIP - double ripper for root extraction
The DuoRIP is a double ripper for excavators.
On requestView product
GRB - excavator grading beam
The GRB is a grading beam for excavators.
On requestView product
Also available
RRB - root rake bucket profile
Root Rakes: Powerful excavation tools designed to efficiently clear stubborn roots and debris.
On requestView product
RRH - hydraulic grab root rakes
Root Grapple Rakes: pull out tough roots and hold them in a hydraulic clamp.
On requestView product
RC - root cutter
Root cutter in three sizes for excavators from 0.6 to 10 t.
On requestView product
Mini & midi excavator attachments
Other mini-ex attachments
Other attachments for mini-excavators.
LR mini - straight land rakes for mini-excavator
Land rakes for excavators: Efficiently clear debris and prepare sites for landscaping or construction.
On requestView product
LRS - short land rakes for mini-excavators
Mini Land Rake: Ideal for tight spaces, this low-profile attachment tackles site prep and debris clearing for mini-excavators.
On requestView product
RIP mini - ripper shank for mini-excavator
Power through tough ground conditions. Mini-Excavator Rippers maximize productivity for efficient trenching and foundation prep.
On requestView product
MR mini - multi-ripper for mini-excavator
Increase mini-excavator versatility. Multi-Rippers tackle tough soil & debris, boosting efficiency in site prep applications.
On requestView productAC mini - asphalt cutter for mini-excavator
Precisely cut through asphalt with Asphalt Cutter for mini-excavators. Featuring a 450mm steel disc, this attachment tackles roadworks, repairs, and utility trenching projects with ease.
On requestView product
GRB light - mini-excavator grading beam with lowered mass
Mini-Excavator Grading Beams: Achieve fast, level finishes for driveways, roads & building pads.
On requestView product
How to choose
- 1
Name the job before the tool
Breaking a surface, loosening ground, pulling roots, levelling and holding are five different jobs, and each one has its own family here. Write down what the crew does most often in a week and the list of candidates usually drops to two.
- 2
Stay inside the carrier weight band
A ripper or a grading beam built for a heavier machine will not fail quietly. It overloads the stick, it upsets the balance of a small carrier, and on a beam it puts the work outside the reach the machine was rated for. Each family page names its band.
- 3
Check the hydraulics for a powered tool
A hydraulic thumb and a grab root rake need an auxiliary circuit and a control in the cab, while a ripper, a rake or a grading beam is passive and needs nothing. Tell us what the carrier already has and we will say which version it can run.
- 4
Match the working width to the site
A wide grading beam finishes a surface in fewer passes but needs room to swing and more machine to carry it; a narrow rake works between plantings. Where access is tight, the smaller model finishes the day sooner than the bigger one.
- 5
Order the tool with the bracket you run
Every tool is built with the bracket system of the coupler on your machine, whether that is S, CW, MS or a pin grabber, or as a direct fit on pins. Give us the system and the size on the quote form and it arrives ready to hang.
Questions we are asked
- What is the difference between a ripper and a multi-ripper?
- A single ripper concentrates the whole force of the machine on one tooth and goes deepest in hard ground. A multi-ripper carries several teeth, moves more material per pass and suits looser, stony soil.
- Which tool pulls out stumps and roots?
- The DuoRIP takes a stump or a root ball out whole with two shanks, and the RRB and RRH root rakes collect roots and cut brush while the soil falls back on the plot.
- Can I use a grading beam on a mini excavator?
- Yes. The GRB mini and the lighter GRB light are drawn for mini carriers and keep the beam mass down, which is what lets a small machine work at full reach safely.
- Does a hydraulic thumb need extra plumbing?
- It needs one double acting auxiliary circuit and a control in the cab. If the carrier has none, we can quote the passive tools that do the nearest job instead.
- Will a tool fit the coupler I already have?
- Yes, if you tell us the system and the size when you ask for the price. We build the bracket for your coupler, and a direct fit on pins is also possible.
Who builds these
- Designed and built in Ostrołęka, Poland, in our own plant.
- 12 months of warranty on every attachment.
- Scheduled for certification to ISO 9001, ISO 14001 and ISO 45001 with UDT: one integrated management system for the whole company.